Walls & Floors — Journal

Acoustic Wall Panel Placement for Open-Plan Offices (2026)

Written by Walls & Floors Inc. | Nov 15, 2026, 8:13:49 AM

Open-plan offices are loud for a simple reason: hard floors, glass partitions and plasterboard ceilings send speech straight back into the room. Conversations from three desks away arrive almost as clearly as the person next to you.

Every phone call adds to the noise. The result is a workspace that works against concentration rather than supporting it.

This guide from Walls & Floors Inc. explains why acoustic wall panels reduce that noise and where to place them for the largest effect. You will find sequenced steps, coverage rules and honest notes on what panels can and cannot do.

Key Takeaways: Acoustic Wall Panel Placement for Open-Plan Offices

  • Start with the ceiling: it is the largest reflective surface and delivers the broadest noise reduction across the floor.
  • Wall panels work at first reflection points, especially on parallel hard surfaces such as glass opposite plasterboard.
  • Plan for 25 to 30 percent coverage of available wall and ceiling area with panels rated NRC 0.80 or higher.
  • Walls & Floors Inc. supplies slatted wood panels on acoustic felt that absorb speech frequencies and scatter mid-range reflections.
  • Panels reduce echo and reverberation inside a room but do not stop sound travelling through walls to the next room.

Why Open-Plan Offices Are So Noisy

Three forces combine in every untreated open-plan office. Hard, reflective surfaces come first. Modern fit-outs favour exposed concrete soffits, glass partitions, polished floors and flat ceilings. These materials reflect sound rather than absorbing it, so reverberation builds and speech intelligibility drops.

No barriers between people come second. Without partitions, a single phone call seven desks away pulls attention from everyone in earshot. Distraction comes from intelligible speech, not raw volume, which is why a noisy canteen can feel easier to work in than a quiet office where one person is on a call.

The Lombard reflex is third. When the ambient noise floor rises, people unconsciously raise their voices. Colleagues then raise theirs. Within minutes the whole floor is louder than it needs to be.

A 2025 study published in the Journal of the Acoustical Society of America confirmed that low-noise environments support individual focused work, while environments above 55 dB disrupt even conversational tasks.

How Acoustic Wall Panels Reduce Office Noise

Acoustic wall panels absorb sound energy before it reflects back into the room. The absorptive core does the work: materials such as mineral wool, glass wool or acoustic felt convert sound waves into small amounts of heat. The result is shorter reverberation time and lower ambient noise.

Slatted wood panels, the type Walls & Floors Inc. supplies, combine two mechanisms. The felt backing absorbs mid and high frequencies where most speech energy sits. The slats scatter the remaining sound, breaking up the flat reflection pattern that makes parallel walls so problematic.

What they do not do: they do not stop sound travelling through the wall itself to the next room. That is a construction issue, not a panel issue.

Reverberation time (often written as RT60) describes how long it takes for sound to decay by 60 decibels after the source stops. In a treated open-plan office, the target is below 0.6 seconds. Untreated offices often exceed 1.0 second.

Panels bring the number down by adding absorptive area to a room that has too many hard surfaces.

What Absorption Values and NRC Ratings Mean for Your Office

Panels are rated using the Noise Reduction Coefficient (NRC) or, under European standards, the weighted sound absorption coefficient (alpha-w). NRC is the average of absorption at 250, 500, 1,000 and 2,000 Hz, the frequencies that carry most speech.

An NRC of 0.80 means the panel absorbs 80 percent of the sound energy at those frequencies. Anything rated NRC 0.80 or above is suitable for office use.

A single headline number can hide differences at individual frequencies. Ask your supplier for the data sheet showing absorption values per mounting method. A panel tested flat against a wall and a panel tested with a cavity behind it give different results, and the mounting you use on site should match the test condition.

When Walls & Floors Inc. quotes acoustic panels, the data sheet comes with the quote. It shows absorption values per frequency band and per mounting method so you can specify correctly. If the numbers you receive show only a single NRC figure without frequency detail, ask for the full report.

Where to Place Acoustic Wall Panels in an Open-Plan Office

Placement matters as much as the product. The goal is to intercept sound at the surfaces where it does the most damage: the ceiling, first reflection points on walls, and parallel hard surfaces. Below is a sequenced approach.

Step 1: Treat the Ceiling First

The ceiling is the largest unobstructed reflective surface in most offices. Sound rises from every workstation and bounces between the hard ceiling and hard floor in a pattern called flutter echo.

Suspended ceiling rafts or baffles hung below the structural ceiling absorb sound on both faces. This makes them more efficient per square metre than a panel fixed flat.

For open-plan offices, plan for ceiling coverage of roughly 20 to 40 percent with panels rated Class A (alpha-w 0.90 or above) over the areas where people sit. This is the single highest-impact intervention.

Step 2: Add Wall Panels at First Reflection Points

First reflection points are the wall surfaces where sound bounces once before reaching a listener. To find them, sit at a desk and have someone slide a mirror along the wall at seated ear height, roughly 1.2 metres from the floor.

Every spot where you can see the sound source reflected in the mirror is a first reflection point and a high-priority position for a panel.

Prioritise these locations:

  • Walls directly behind or facing desk clusters
  • Any pair of parallel hard surfaces, especially glass opposite plasterboard
  • Walls adjacent to meeting rooms and call booths
  • Corridors and breakout zones that funnel noise back into the main floor

Step 3: Address Parallel Hard Surfaces

Two bare walls facing each other create flutter echo, a rapid series of reflections that produces a metallic ringing quality on every voice. Treat at least one wall of each pair. Staggering panels along the wall breaks up the reflection path without requiring full coverage.

Glass partitions are among the most reflective surfaces in any building. If your office has glass on one side and plasterboard on the other, panels on the plasterboard wall make the most difference.

Step 4: Fine-Tune with Desk-Level Treatment

Acoustic screens between desks block the direct sound path between people sitting close together. A screen needs to be tall enough to break the line of sight between seated heads, typically 1.2 to 1.5 metres from floor level.

Screens do not reduce the reverberation of the room, so they work only after the ceiling and walls have been addressed.

How to Calculate Coverage for Your Office

For most open-plan offices with standard ceiling heights of 2.7 to 3.5 metres, aim for treatment covering 25 to 30 percent of available wall and ceiling area with NRC 0.80 or higher panels.

In a 500 square metre office with 3 metre ceilings, the total available treatment surface is roughly 860 square metres. At 25 percent coverage, that is approximately 215 square metres of panels.

That number sounds large but panels concentrate at high-impact positions: the ceiling above desk areas, the perimeter walls at first reflection points, and any large flat surfaces facing workstations. Not every square metre of wall needs treatment.

Start with the calculation, then adjust based on a site measurement. A clap test gives a rough indication: clap once in the empty room. If you hear a ringing or fluttering tail, the room still has too many hard reflective surfaces. Add panels while the ring persists and stop when speech sounds dry and close.

How to Create Acoustic Zones in an Open-Plan Office

Acoustic zoning means dividing the floor into areas designed for different activities, then matching the treatment to each one. This is the highest-impact intervention at the planning stage and costs nothing if it happens before the fit-out.

Focus Zones for Concentrated Work

Focus zones sit away from circulation routes, kitchens and breakout space. Treatment is dense: high-absorption ceiling panels above, acoustic wall panels on adjacent surfaces, and screens between desks. A sound-masking system can lift the noise floor evenly so any remaining speech becomes unintelligible. Target a reverberation time under 0.5 seconds.

Collaboration Zones for Team Work

Collaboration zones host short meetings, stand-ups and informal conversations. The treatment goal is twofold: keep speech intelligible inside the zone and prevent it leaking into adjacent focus space.

Suspended baffles overhead and absorptive wall panels on the nearest hard surface deliver both. Position these zones with at least one solid wall and a buffer of soft furniture between them and focus areas.

Social Zones for Breakout and Kitchen Areas

Kitchens and breakout areas are the loudest spaces on the floor by design. Locate them as far from focus zones as the floor plate allows, and treat them heavily.

Absorptive ceiling treatment, wall panels, soft seating and rugs work together to keep reverberation low and stop the social space spilling noise into the rest of the office.

Choosing the Right Panel Material for Your Office

Several panel types suit open-plan offices. The right choice depends on the absorption target, the mounting surface and the finish you need.

Slatted Wood Panels on Acoustic Felt

This is the type Walls & Floors Inc. supplies. The slats are real wood veneer in finishes including natural oak, smoked oak and walnut. The acoustic felt behind the slats absorbs speech frequencies, and the slat pattern scatters remaining reflections.

Panels are sold per square metre with mounting profiles included. They suit offices, lobbies, meeting rooms and hospitality spaces where the treatment needs to look as considered as the rest of the interior.

A colour on screen is not a colour on site. Order a sample and hold it against your floor and ceiling before you specify. Walls & Floors Inc. sends samples free, and they leave within two working days.

Fabric-Wrapped Mineral Wool or Glass Wool Panels

These panels deliver high absorption (typically NRC 1.00) across the speech frequency range. They are available in a wide range of fabrics and suit offices where maximum acoustic performance is the priority. Thickness matters: a 50 mm panel absorbs meaningfully lower into the frequency range than a 25 mm one.

PET Felt Panels

PET felt is lightweight, cuts cleanly and comes in a wide colour range. Performance varies with thickness. A 9 mm PET panel fixed flat to a wall is closer to decorative than functional.

The same material at 24 mm, or at 9 mm with an air gap behind it, performs noticeably better. Always check the published absorption data and the mounting condition it was tested in.

What Acoustic Wall Panels Cannot Do

Panels reduce echo and reverberation inside a room. They do not block sound from passing through walls, floors or ceilings. If you can hear the next room clearly, the fix is in the wall itself: mass, airtight seals, a solid door with gaskets and a sweep. Panels will not solve that problem.

Panels also cannot create silence. The goal in an open-plan office is not zero noise. It is a lower background level and clearer speech close by, so people can work without fighting the room. A well-treated office sits at roughly 50 to 55 dB(A). An untreated one typically runs at 65 to 70 dB(A).

Sound masking can supplement panel treatment. It adds a low, continuous broadband sound through ceiling-mounted emitters, raising the noise floor by a few decibels and rendering speech unintelligible beyond a short distance. Masking works alongside panels, not instead of them.

Planning a Panel Placement Project: A Step-by-Step Checklist

If you are an office planner or facility manager preparing to treat an open-plan space, use this sequence. Each step has a reason attached.

  1. Map the floor by activity. Mark focus zones, collaboration zones, social zones and quiet zones on the floor plan. This determines where treatment is dense, moderate or light.
  2. Measure the room. Record length, width and ceiling height for each zone. Calculate the total wall and ceiling area.
  3. Set coverage targets. Use 25 to 30 percent of available surface area as a starting point. Focus zones need more. Social zones may need less on walls if the ceiling is fully treated.
  4. Identify first reflection points. Use the mirror method at seated ear height. Mark these positions on the drawing.
  5. Choose the panel type. Match the NRC to the target, the finish to the interior and the mounting to the substrate. Ask the supplier for a data sheet showing both absorption values and fire classification.
  6. Plan the ceiling treatment. Specify suspended rafts or baffles above the busiest desk clusters and collaboration zones first.
  7. Coordinate with services. Check that panel and baffle positions do not conflict with sprinklers, lighting or HVAC. Suspended panels need access at height, so schedule installation outside working hours for those areas.
  8. Order samples. Hold finishes against the floor and existing surfaces before committing. Walls & Floors Inc. sends free samples within two working days.
  9. Install zone by zone. Start with the loudest or most complained-about area. One well-treated focus zone is worth more than panels scattered across the floor.
  10. Test after installation. Do a clap test in each zone. If the ringing tail is gone and speech sounds dry at two metres, the treatment is working.

Common Placement Mistakes and How to Avoid Them

Covering one wall heavily and leaving the rest bare is the most frequent error. A spread layout, with panels distributed across multiple surfaces, exposes more panel perimeter to the room and performs better than the same panels grouped together. Spread, do not stack.

Mounting panels too high is the second mistake. Keep panel centres between seated ear height (roughly 1.2 metres) and 3.5 metres above the floor. Above that, sound energy reaches the panel too late to control early reflections where they matter most.

Treating walls without treating the ceiling is the third. The ceiling carries the largest share of the acoustic workload in an open-plan office. Panels on walls alone will improve things, but the step change comes when the ceiling is treated as well.

Skipping the data sheet is the fourth. A panel marketed as “acoustic” with no published NRC or alpha-w figure may absorb very little at the frequencies that matter. Ask for test data before you specify.

How Fire Classification Affects Panel Selection

In commercial buildings, wall and ceiling linings must meet fire safety requirements. In the EU, panels are classified under EN 13501-1, ranging from Euroclass A1 (non-combustible) to Euroclass F. In the UK, the relevant classification is also Euroclass, with Approved Document B referencing EN 13501-1 for wall and ceiling linings.

Ask the supplier for the fire classification document before you order. Walls & Floors Inc. includes the fire classification with every quote so you can pass it directly to the specifier or building control. If you need a specific Euroclass rating, state it on the enquiry and we confirm availability before quoting.

How Walls & Floors Inc. Supports Your Acoustic Panel Project

Walls & Floors Inc. supplies slatted wood acoustic wall panels on acoustic felt backing for offices, meeting rooms, lobbies and hospitality spaces across the Netherlands. The panels come in natural oak, smoked oak and walnut, sold per square metre with mounting profiles included.

Every quote names a delivery week. Samples are free and leave within two working days. The data sheet showing absorption values per mounting method and fire classification comes with the quote, so you can specify with the numbers in front of you.

If the site has restricted access, a narrow street or a tight delivery window, tell us on the enquiry. We adjust the vehicle size and the delivery plan to match the conditions. One contact person stays with your project from quote to handover.

In Conclusion: How to Plan Acoustic Wall Panel Placement for a Quieter Office

A quieter open-plan office starts with the ceiling, moves to first reflection points on walls, and finishes with desk-level screens and soft furnishings. Plan coverage at 25 to 30 percent of available surface, choose panels rated NRC 0.80 or higher, and treat the loudest zone first.

Panels reduce echo and reverberation inside the room. They do not soundproof it. If you need privacy between rooms, that is a wall and door problem. If you need a calmer, clearer workspace, panels are the fix.

Order a free sample from Walls & Floors Inc. and hold it against your floor at four in the afternoon. That is the test that matters. Samples leave within two working days.

FAQs About Acoustic Wall Panel Placement for Open-Plan Offices

Where should acoustic panels go first in an open-plan office?

Treat the ceiling first. It is the largest reflective surface and delivers the broadest reduction in reverberation. After the ceiling, add wall panels at first reflection points, especially on walls that face glass partitions or other hard surfaces.

How many acoustic panels does an open-plan office need?

Plan for panels covering 25 to 30 percent of available wall and ceiling area, using products rated NRC 0.80 or higher. The exact number depends on ceiling height, floor area and how much absorption is already in the room from furniture and flooring.

Do acoustic panels soundproof an office?

No. Acoustic panels absorb sound inside a room, reducing echo and reverberation. They do not stop sound passing through walls, floors or ceilings. Blocking sound between rooms requires mass, airtight seals and a solid door. Walls & Floors Inc. states this clearly because it affects what you can expect from the treatment.

What NRC rating should office acoustic panels have?

Office acoustic panels should be rated NRC 0.80 or higher. Panels in the 1.00 range absorb nearly all speech-frequency energy. Always ask for the full data sheet rather than relying on a single headline number, because absorption varies by frequency and mounting method.

How does Walls & Floors Inc. help with acoustic panel projects?

Walls & Floors Inc. supplies slatted wood panels on acoustic felt in natural oak, smoked oak and walnut. Every quote includes a named delivery week, a data sheet with absorption values per mounting method, and fire classification documentation. Free samples leave within two working days so you can judge the finish against your own surfaces.

Can acoustic panels be installed while the office is in use?

Wall panels and most surface-fixed products can be installed zone by zone during working hours with limited disruption. Suspended ceiling products need access at height, so those areas are better done outside office hours. Discuss scheduling with your supplier before work begins.

What is the difference between absorption and soundproofing?

Absorption reduces the sound bouncing around inside a room. Soundproofing stops sound passing between rooms. Panels handle absorption. Soundproofing requires heavier construction: dense walls, sealed gaps, solid doors with gaskets. Walls & Floors Inc. supplies absorption panels, not soundproofing systems, and we say so because it matters for your specification.